gtag('config', 'G-J1B3LVWC4M');
Show basket (0 Article) My accountTo checkout

AquaCon™

Buy Smooth-On at FormX

Smooth-On is one of the worlds leading manufaturers 3D modeling materials such as mold-making, casting and special effects materials but also industrial casting resins, adhesives and equipment. FormX is main distributor of Smooth-On products in Europe.

AquaCon™ is a water based concrete release agent that aids in releasing concrete castings from Smooth-On rubber molds and other surfaces such as melamine, metal and non-porous (sealed) wood. It provides a clean, positive release, does not interfere with color or surface detail and helps minimize bug holes and air bubbles in finished castings. Coverage – Applied in a thin film (.0005 in / .013 mm), 1 gallon (undiluted) covers 3,200 square feet / 297 square meters.

Features
- Low Cost – Use straight or dilute with water (up to 8 parts with water. See dilution recommendation below).
- Water Based, Eco-Friendly – Contains no VOC’s, carcinogens or oils harmful to the environment.
- Does Not Stain Concrete, affect color surface detail or finishing.
- Minimizes “Bug Holes” and air bubbles.
- Contains No Oils that will cause rubber molds to soften, shrink or swell.
- Keeps Molds Clean - Does not build up.
- Extends Mold Life

Product

Aquacon

Video
Instructions

PREPARATION... Safety - Wear safety glasses to minimize contamination risk. Store and use at room temperature 23°C. Do not use below 8°C.

Pre-Mixing - Before dispensing, shake container or stir thoroughly with a paddle or drill mixer set on a slow speed to a uniform consistency.

Diluting AquaCon™ - AquaCon™ can be used straight or diluted with up to 8 parts water. The dilution ratio depends on your concrete mix design. Finding the right balance between AquaCon™ and water can affect bug holes. If using on a new rubber mold, it is recommended that AquaCon™ be used straight (undiluted) for each casting for the first 10 castings. 1 – 10 castings, use undiluted. After 10 castings, dilute 1 part AquaCon™ : 4 Parts Water After 20 castings, dilute 1 part AquaCon™ : 8 Parts Water Mix only amount needed for one day. Mixture may separate in the container after a few hours. Before dispensing, pre-mix before to a uniform consistency.

Applying - Coat mold surface with a very thin film (.0005 in / .013 mm). Apply with a brush, roller, HVLP gun or Kwikee™ Sprayer. Do not allow release agent to pool in the mold. Wipe over mold surface using a clean, soft cloth.

Caution: Do Not Over Apply. Applying too much release agent will cause air bubbles “wormtracks”, “bugholes” or pitting on surfaces. After applying AquaCon to mold surface, you can mix and cast concrete immediately.

Mixture may separate after 24 hours. If mixture separates, re-mix to a uniform consistency and apply. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question

GUIDE

Let us help you find your way.

The list below may help you find what you are looking for via an alternative path.

  • Molding

    flexible and rigid molding for all sorts of objects.

  • Casting

    a wide range of flexible and rigid casting materials.

  • Special Properties

  • Composites

    resins, poyester, epoxy, acrylic resin, glass fibres etc.

  • Foam

    expanding flexible and rigid foams, rigid blocks.

  • Restoration

    restoring in- and exterior ornaments and buildings.

  • Prototyping

    resins and other materials used for rapid prototyping.

  • Textile

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

FormX Newsletter About us Contact Shipping Applications we have vacancies Terms of Sale

Wir verwenden Cookies um unsere Website zu optimieren und Ihnen das bestmögliche Online-Erlebnis zu bieten. Mit dem Klick auf "Alle akzeptieren" erklären Sie sich damit einverstanden. Erweiterte Einstellungen