gtag('config', 'G-J1B3LVWC4M');
Show basket (0 Article) My accountTo checkout

Ecoflex™ GEL /0,91 kg

Ecoflex™ GEL

Ecoflex™ GEL is an extremely soft, platinum silicone rubber gel specifically designed for creating silicone makeup appliances, for cushioning, creating gaskets, encapsulation, and other applications requiring a very soft silicone material.

Certified Skin Safe - Cured Ecoflex™ GEL is skin safe and is certified by an independent laboratory. OECD TG 439 certification. No animals were used in testing.

Features

Ecoflex™ GEL has a Shore hardness of 000-35, this is below the Shore 00 hardness scale. Because Ecoflex™ GEL is so soft, it works very well as a silicone gel for filling encapsulated silicone makeup appliances and prosthetics. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments.

As Ecoflex GEL is very tacky when cured, in some situations, it is recommended that Ecoflex™ GEL be encapsulated with another non-tacky platinum silicone such as Dragon Skin FX Pro, or another suitable membrane. Ecoflex™ GEL is mixed 1A:1B by weight or volume. Rubber cures at room temperature 23°C with negligible shrinkage

Ecoflex™ GEL
working time is 15 minutes - Cure time is 2 hours - Color translucent.

38,05 EUR

incl. 21% VAT excl. transport
Weight: 1.2 kg
set (A+B)


Instructions

Preparation - Materials should be stored in and used at room temperature 23°C. These products have a limited shelf life and should be used as soon as possible. Rubber may be inhibited by sulfur based clays resulting in tackiness at the surface interface or a total lack of cure throughout the mold.

If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of rubber onto a non-critical area. Inhibition has occurred if the rubber is gummy or uncured after the recommended cure time has passed.

USING ECOFLEX™ GEL FOR MAKING SILICONE PROSTHETIC MAKEUP APPLIANCES - Ecoflex™ GEL can be used as a gel filler for creating silicone prosthetic appliances. In most cases, Ecoflex™ GEL should be encapsulated. For example, Dragon Skin™ FX-Pro can be stippled onto a mold surface (e.g. Shell Shock™ released with Ease Release™ 200) to create a membrane. Ecoflex™ GEL can then be poured or injected into the mold to create a soft gel prosthetic encapsulated with strong, non-tacky Dragon Skin™ FX-Pro silicone.

Applying a Release Agent - Although not always necessary, a release agent will make demolding easier when casting into most surfaces. Ease Release™ 200 available from Form x is a proven release agent for releasing silicone from silicone or other surfaces.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MEASURING & MIXING -
Before you begin, pre-mix Part B thoroughly. After dispensing required amounts of Parts A and B into mixing container (1A:1B by volume or weight), mix thoroughly making sure that you scrape the sides and bottom of the mixing container several times. For best results, ‘double mix’ the material by pouring the mixture into a new container, then continuing to mix until material is thoroughly blended.

Pouring - For best results, pour your mixture in a single spot at the lowest point of the containment field or mold. Let the rubber seek its own level. A uniform flow will help minimize entrapped air.

Curing - Allow rubber to cure for 2 hours at room temperature 23°C before demolding. Time to demold can be reduced with mild heat or by adding an appropriate amount of Plat-Cat™ cure accelerator. The pot life and cure times can be extended using Slo-Jo™ cure retarder. Do not cure rubber where temperature is less than 18°C.

Guide

Let us help you find your way.

The list below may help you find what you are looking for via an alternative path.

  • Molding

    flexible and rigid molding for all sorts of objects.

  • Casting

    a wide range of flexible and rigid casting materials.

  • Special Properties

  • Composites

    resins, poyester, epoxy, acrylic resin, glass fibres etc.

  • Foam

    expanding flexible and rigid foams, rigid blocks.

  • Restoration

    restoring in- and exterior ornaments and buildings.

  • Prototyping

    resins and other materials used for rapid prototyping.

  • Textile

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

FormX Newsletter About us Contact Shipping Applications we have vacancies Terms of Sale

Wir verwenden Cookies um unsere Website zu optimieren und Ihnen das bestmögliche Online-Erlebnis zu bieten. Mit dem Klick auf "Alle akzeptieren" erklären Sie sich damit einverstanden. Erweiterte Einstellungen